Custom Knurled Pins - Machined Hardware Source https://www.machinedhardwaresource.com/portfolio-category/custom-precision-straight-diamond-knurled-pins/ Custom machined fasteners and hardware - custom nuts, custom standoffs, custom spacers, custom pins, and much more Wed, 03 Apr 2019 16:46:10 +0000 en-US hourly 1 https://wordpress.org/?v=6.4.3 194122541 Custom Diamond Knurled Stainless Steel Pins https://www.machinedhardwaresource.com/portfolio/custom-diamond-knurled-stainless-steel-pins/ Wed, 03 Apr 2019 16:46:10 +0000 https://www.machinedhardwaresource.com/?post_type=liquid-portfolio&p=4896 The post Custom Diamond Knurled Stainless Steel Pins appeared first on Machined Hardware Source.

]]>

These are stainless steel knurled pins made to a customer’s print at a quantity of just over 500 pieces.  They measure approximately .800″ in length at a diameter of .118″.  Ofcourse the most interesting requirement is the diamond knurling of .150″ at each side that is intended to bite into the plastic setting.  In order to increase the diameter at the knurled ends and allow for better locking into the plastic the factory adjusted their method to allow for very aggressive knurling, thereby pushing the material further and increasing the overall diameter at both sides.  No machining or deburring was done on either side after this process to preserve this increased diameter.

The post Custom Diamond Knurled Stainless Steel Pins appeared first on Machined Hardware Source.

]]> 4896 Custom Stainless Pins With One Side Diamond Knurled https://www.machinedhardwaresource.com/portfolio/custom-stainless-pins-with-one-side-diamond-knurled/ Wed, 03 Apr 2019 16:43:41 +0000 https://www.machinedhardwaresource.com/?post_type=liquid-portfolio&p=4894 The post Custom Stainless Pins With One Side Diamond Knurled appeared first on Machined Hardware Source.

]]>

Similar to the other knurled pin we supply, this is a stainless steel pin manufactured in the USA with a single diamond knurled side.  Made the same way, the knurling is done aggressively to push the material and expand the outside diameter beyond that of the smooth shoulder portion.  The pin measures approximately .980 in length +.005/-.000 and the outside diameter of the smooth shoulder is .118 +/-.0005.  The outside diameter of the knurled side however is .150 +/-.005.  32-35 pitch is used on the knurling.

The post Custom Stainless Pins With One Side Diamond Knurled appeared first on Machined Hardware Source.

]]> 4894 Custom Partially Knurled Pins In Plain Steel Material https://www.machinedhardwaresource.com/portfolio/custom-partially-knurled-pins-in-plain-steel-material/ Tue, 02 Apr 2019 21:44:11 +0000 https://www.machinedhardwaresource.com/?post_type=liquid-portfolio&p=4879 The post Custom Partially Knurled Pins In Plain Steel Material appeared first on Machined Hardware Source.

]]>

These are custom partially knurled pins made using plain low carbon steel material.  One side is threaded at 6-32 with approximately .375 inches of thread while the other is diamond knurled at .20 inches max.  Overall length is set at .855 inches.  Production was done domestically at approximately 1,000 pieces.

Our relationships with factories all over the United States and abroad based on decades of custom hardware & fastener production history, in combination with the flexibility of blanket purchase arrangements, allows us to fully cater to the customer’s hardware specification and procurement requirements.

The post Custom Partially Knurled Pins In Plain Steel Material appeared first on Machined Hardware Source.

]]> 4879 Custom Knurled Pins – 41L40 Steel Material https://www.machinedhardwaresource.com/portfolio/custom-knurled-pins-41l40-steel-material/ Tue, 02 Apr 2019 21:00:05 +0000 https://www.machinedhardwaresource.com/?post_type=liquid-portfolio&p=4866 The post Custom Knurled Pins – 41L40 Steel Material appeared first on Machined Hardware Source.

]]>

Over the years we have provided countless custom knurled hardware pieces – below is a snapshot of a custom bolt we are working on producing for a customer that is intended to be hammered into a predrilled steel plate.  We noticed that the spec calls out for diamond knurling but realized that probably won’t work for the intended purpose, which is to keep the bolt from spinning after being inserted.

After discussing it with the factory engineers we suggested going with a straight knurl instead of the diamond knurl.  The straight knurl would work better in keeping engagement.  We put together these samples to allow our customer to test the idea before incorporating it fully into the production run.  The production parts would be made using the same 41L40 steel material with a zinc plated finish.

The post Custom Knurled Pins – 41L40 Steel Material appeared first on Machined Hardware Source.

]]> 4866